Multitronix
  • Home
  • Products
    • Kate 2 Transmitter
    • Kate 2 Pyro Board
    • Kate 1 Transmitter
    • Receiver
    • Turn-on Coil
    • Carrying Case
    • Nosecones
    • Specifications
  • Buy
  • Software
  • Firmware
  • Documents
  • Flights
    • 142K Flight
    • 118K Flight
    • 96K Flight
    • 90K Flight
    • 40K Flight
    • 28K Flight
    • 16K Flight
  • About
  • Contact
Kate 2.0 Transmitter
Kate 2.0 TelemetryPro® Transmitter
The new Kate 2.0 transmitter has all the same features as the original Kate 1.0 transmitter plus a lot more!  It features a GPS with unlimited altitude capability.  It can be used to track extremely high altitude flights and capture the maximum altitude with GPS precision.  Nearly every other GPS tracker being sold for use in hobby/amateur rockets is limited to a maximum operational altitude of 50km (164K feet).  There is one that does operate at higher altitudes but it has a GPS module that resets itself when it transitions down from high speed.  Therefore, it has to re-acquire and re-lock onto all the GPS satellites as it approaches a high altitude apogee.  This can take some time and runs a risk of not having a good GPS fix at apogee.   This does not happen with Kate 2.0.  The Kate 2.0 GPS module never resets during flight.
Picture
MORE INFORMATION
Deployment and Staging Capability
Another significant new feature of the Kate 2.0 transmitter is an optional add-on pyro board that adds deployment and staging capability.  This means an apogee event can be fired with GPS precision even at altitudes that reach into space.  The pyro board has seven firing channels plus one solid state relay output.   GPS and gyro tilt lockout are included for safe staging.  Power-on and arming can be done remotely for added safety.  There is also a built-in safety shunt for the sustainer motor igniter channel.  Deployments and staging events can be configured using the Mx120 Receiver.  No computer needed.  Deployment and staging events can be triggered based on a flexible combination of GPS, accelerometer, gyro, barometric pressure, timer, or manual command.  There are also two general purpose inputs for monitoring external events.  Multiple mounting configurations are supported for the pyro board.
Picture
MORE INFORMATION

Transmitter
Original Kate 1.0 TelemetryPro® Transmitter
  • 900 MHz one watt transmitter with smart power management.
  • ​Range exceeds 300,000 feet.
  • Li-ion battery with onboard charger.  More than five hours of standby time.
  • Ublox-7 GPS operating in high dynamics mode with five updates per second.
  • Large, high gain GPS antenna for best satellite lock.
  • Robust mechanical design supports and protects antennas, battery and all electronics.
  • Mounts in a standard 54mm tube inside a nosecone and is held in place using 54mm liner tubes above and below it.
  • Ready to fly. No sled to build, no wiring required.  This is not a "bare board" product.
  • Completely self-contained. Easy to move from one rocket to another.
  • Onboard 50G accelerometer is recorded at 100 readings per second.
  • All flight data is saved in onboard flash memory for post flight analysis.
  • Built-in USB interface for off-loading flight data and recharging the battery.
  • Seven LED status indicators:  Flight Mode, Config Mode, Linked, USB Activity, Charging, Charge Done, Charge Failed.
  • Approved by the Tripoli Rocketry Association for altitude contests and records.
Picture
MORE INFORMATION

Picture
TelemetryPro® Receiver
  • Fully integrated handheld receiver with antenna, display, buttons, and internal GPS.  
  • LCD display is fully readable in direct sunlight.
  • Easy to use and very intuitive.  Simple menu driven user interface with on-screen cursor.
  • Interactive pre-launch go/no-go status display guides user with setup when getting ready to launch.
  • All of the live telemetry data is displayed on screen in real time during the flight.
  • A synthesized voice (Kate) reports rocket trajectory in real time during the flight. Speaker is built-in. An audio output jack is also available for connecting Kate into the launch PA system. It is fun to listen to Kate while watching the flight. This also enhances safety by letting everyone know exactly what is happening in real time. Especially if the rocket has gone out of sight.
  • Flight data and Kate audio commentary from four flights can be saved to internal flash memory.  The data and audio can also be downloaded over USB for post flight analysis and play back.
  • A locator screen shows distance and direction to the landing site.  Very easy to use for rocket recovery. 
  • A special map mode shows the rocket location in real time on a map displayed on a tablet or laptop.
  • Selectable transmitter ID codes allow any receiver to operate with any transmitter. This allows multiple users to share one receiver. Multiple receivers can also be used for redundancy to simultaneously track one rocket.
  • High performance circularly polarized antenna eliminates signal loss due to transmitter orientation during the flight.  There is a five segment signal strength indicator displayed on screen at all times.
  • Flight simulation mode for initial familiarization and practice before an actual flight. 
  • Status displays for both the transmitter and the receiver batteries.
  • Requires four standard AA alkaline batteries.
Picture
MORE INFORMATION

Picture
TelemetryPro® Turn-On Coil
  • The transmitter can be powered-on by passing the turn-on coil around and down the outside of the nosecone.
  • No access hole to the transmitter power switch is needed.
  • Turn-on coil is optional but very handy!
  • One button operation.
  • Green LED indicator shows battery status and that the unit is operating.
  • Requires one 9V alkaline battery.
  • The transmitter can be powered-off by sending a command from the receiver.
Picture
MORE INFORMATION

Picture
TelemetryPro® Carrying Case
  • Tough, rugged and lightweight
  • Airtight and watertight
  • Easy opening ​Press & Pull® latches
  • Soft-grip, solid-core carrying handle
  • Precision cut anti-static polyurethane/ester foam
  • Injection molded HPX® high performance resin
  • Dent-resistant and shatter-resistant
  • Silicone o-ring seal
  • Two molded-in hasps for padlocks
  • TelemetryPro System decal in recessed area on lid
  • Permanently attached Vortex® pressure relief value
  • 18.2" x 13.4" x 6.7"   (462 x 340 x 170 mm)
  • 6.4 lbs (2.9 kg) weight for case with foam
Picture
MORE INFORMATION

Picture
TelemetryPro® Transmitter Nosecones
Picture
MAC Performance Rocketry sells some very nice "Ready-to-Fly" nosecones that are specifically built to hold the TelemetryPro transmitter.  They are available in 3" and 4" sizes in either fiberglass or plastic.  They use a PVC threaded closure with a Kevlar lanyard.  This eliminates any metal parts from being near the transmitter downlink antenna yet is very secure.

The fiberglass nosecone is filament wound and has a canvas phenolic coupler that is exceptionally strong.  The tip on the fiberglass nosecone is aluminum.

These are high quality nosecones that eliminate the need to build your own.  They are Multitronix approved!
​
Picture
View nosecones available at MAC Performance Rocketry
Picture
View photos of nosecone construction

Picture
BUY NOW
TelemetryPro... "when failure is not an option"

TelemetryPro® is a registered trademark of Multitronix LLC

Multitronix LLC reserves the right to change or obsolete products without prior notice.

Website copyright © 2014, 2015, 2016, 2017, 2018, 2019, 2020
Multitronix LLC       All Rights Reserved